Skip to content

Inspection & Maintenance Updated 3 min read

Used Excavator Inspection Checklist: What to Check Component by Component

A component-by-component checklist for inspecting a used excavator — engine, hydraulics, undercarriage, boom and arm, swing, chassis and cab — plus the evidence to request when buying remotely.

By Yingju Machinery Export Team

Used Excavator Inspection Checklist: What to Check Component by Component

A used excavator inspection should cover identity and history, engine, hydraulics, undercarriage, boom and arm, swing system, chassis, and the cab and controls. Use this checklist on site or to review the photos and videos a seller sends you. It is a screening tool: findings such as excessive play or unexplained welding are reasons to call in a specialist, not automatic pass/fail results.

Identity and history

Start by confirming the machine is what the listing says. Photograph the serial plate and compare it with the documents. Record the hour-meter reading and compare it with visible wear. Ask about known accidents, structural repairs, rebuilt components and service records. A seller should disclose known major repairs; Yingju Machinery does so for every unit it sells.

Engine

Always watch a cold start — a warm engine hides problems. Look for hard starting, heavy smoke that does not clear, knocking and unstable idle. Check for oil and coolant leaks, the condition of belts and hoses, and blow-by from the breather. Note radiator condition, especially for machines going to hot climates.

Hydraulic system

Run every function: boom up and down, arm in and out, bucket curl, swing and travel. Functions should be smooth and reasonably quick under load. Watch for cylinders drifting when holding a load, which can indicate internal seal wear. Inspect hoses, fittings, cylinder rods (for scoring and pitting) and the pump compartment for leaks.

Undercarriage

The undercarriage is often the most expensive wear area on a crawler excavator. Check track links and pins, rollers, idlers and sprockets for wear, and look for cracked track shoes. Check track tension and look for oil leaks from the final drives. Uneven wear between the two sides can point to alignment problems or hard use on slopes.

Boom, arm and bucket

Inspect the boom and arm for cracks, especially around welds, mounting bosses and the cylinder brackets. Fresh paint over a specific area or unexplained welding deserves closer examination. Check pin and bushing play at each joint by moving the bucket slightly with the engine running, and look at bucket teeth, cutting edge and linkage wear.

Swing system

Swing the upper structure in both directions and listen for grinding. With the bucket on the ground, check for excessive play in the slew ring. Slow or jerky swing can indicate issues with the swing motor or gearbox.

Chassis, cab and controls

Inspect the chassis, counterweight and lower frame for impact damage. In the cab, confirm gauges and warning lights work, controls respond correctly and safety features such as the seat belt and lock lever are present. Check the air conditioning if the machine will work in a hot climate.

Working hours: reading versus verified history

An hour-meter photograph shows the recorded reading, not the full operating history of the machine. Meters can be replaced or fail, so compare the reading with physical wear: pedal and seat wear, pin and bushing play, undercarriage condition and the state of the bucket. Service records and parts invoices are stronger evidence than the meter alone. When wear and recorded hours do not match, treat the hours as seller-reported and price the machine on its condition.

Evidence to request when buying remotely

ComponentEvidence to request
IdentitySerial plate and hour-meter photos
EngineContinuous cold-start video
HydraulicsHydraulic-cycle video of all functions under load
UndercarriageClose-ups of links, rollers, idlers and sprockets from both sides
Boom and armClose-ups of welds and joints; repair disclosure
OverallThird-party inspection report where available

Yingju Machinery provides cold-start videos, hydraulic-cycle tests and inspection photos on request, and facilitates third-party inspections at its Hefei yard. Browse used excavators or read more about our inspection services.

inspection checklistused excavatorundercarriagehydraulics

Written by

Yingju Machinery Export Team

The export team at Hefei Yingju Mechanical Equipment Co., Ltd. has sourced, inspected and shipped used construction machinery from Hefei, China.

From the yard

Used excavators you can request files for

All used excavators →

Related guides

Request a Quote

Turn the checklist into a quotation.

Tell us the machine, quantity and destination port. We send photos, videos, the inspection report and an itemized quote — replies within 24 hours.

Request a Quote

Tell us what you need

Share the machine, quantity and destination port. You will receive an itemized quotation with photos and inspection videos on request.

We reply within 24 hours. Your details are used only to answer your inquiry — see our privacy policy.

Built with PolyDraft